The base measurement
A ring is defined by its inside circumference (the distance around the inside of the band). Inside diameter is circumference ÷ π. We store the circumference in millimetres and derive everything else from it, which is the approach ISO 8653 takes.
System definitions
| System | Rule | US 7 example |
|---|---|---|
| US / Canada | Inside diameter (in) = 0.458 + 0.032 × size. Size 0 is 11.63 mm; each whole size adds 0.8128 mm. Quarter sizes are supported. | 17.32 mm across, 54.42 mm around |
| ISO 8653 / France | The inside circumference in mm, usually shown to one decimal. | 54.4 |
| Germany | The inside diameter in mm. | 17.3 |
| Italy / Spain / Switzerland | Inside circumference − 40 mm. | 14.4 |
| UK / Australia / NZ | 1987 British metric scale: size C = 40 mm circumference, +1.25 mm per letter, +0.625 mm per half size. Above Z½ we label Z+1, Z+1½ and so on in the same steps. | N½ (54.38 mm) |
| Japan (JCS) | Inside diameter (mm) = 13 + (size − 1) ÷ 3, sizes 1 to 30. | 14 (17.33 mm) |
Worked example
- You measure a ring at 17.3 mm across the inside.
- Circumference = π × 17.3 = 54.35 mm.
- US size = (17.3 ÷ 25.4 − 0.458) ÷ 0.032 = 6.97, which rounds to the nearest quarter: US 7.
- ISO 54.3 · German 17.3 · Italian 14.3 · UK: (54.35 − 40) ÷ 1.25 = 11.5 letters above C, which is N½ · Japan: (17.3 − 13) × 3 + 1 = 13.9, which rounds to 14.
Rounding and “between sizes”
Tools show the nearest quarter US size and flag a result as “between” when it is more than 0.05 of a size from a quarter step; both neighbours are shown. UK results round to the nearest half size and Japanese results to the nearest whole size. Tables show measurements to two decimals and system sizes to one.
The UK scale question
The UK has no current national standard for ring sizes, so UK retailers use one of two historical scales that differ by about half a size. We use the 1987 metric scale because it is defined in millimetres, which makes every conversion checkable with a ruler. If a seller’s chart puts your UK letter half a size away from ours, trust the measurement in millimetres and the seller’s own chart for that ring.
How we check the numbers
- The sizing engine has automated tests for the anchor values above (US 7 = 17.3228 mm = 54.42 mm; US 6 = UK L½; US 7 = Japan 14) and for the engine’s input limits (10 to 30 mm diameter). The calculators on the site accept a narrower range, 12 to 25 mm inside diameter (about US ½ to 16¼), which covers real ring sizes and catches unit mistakes.
- Every table on the site is generated from the engine at build time, so a chart cannot drift from the calculator.
- Printable sheets are checked with a ruler after printing on real printers, and each carries a 100 mm bar so you can repeat the check.
- Corrections are listed below with the date.
Limitations
- Ring size standards are national conventions, not laws; a retailer may size slightly differently. For an expensive ring, confirm with a jeweller’s gauge.
- Wide bands (over about 6 mm) and comfort-fit interiors usually need a quarter to half size larger than the measurement suggests.
- Smart rings use brand-specific sizing kits that do not match standard scales.
Sources
- ISO 8653:1986, Jewellery — Ring-sizes — Definition, measurement and designation (defines ring size by inside circumference in mm).
- US sizing: the industry formula diameter = 0.458 in + 0.032 in × size, as used by US ring gauges and mandrels.
- UK: the 1987 British metric letter scale (C = 40 mm, 1.25 mm per letter), as used in UK trade size charts. The former British Standard for ring sizes was withdrawn and has not been replaced.
- Japan: Japan Custom Size (JCS) table, 13 mm for size 1 with ⅓ mm steps, as published by Japanese jewellers.
Change log
- 3 November 2026 – First published. UK scale set to the 1987 metric scale; Japanese sizes 1–30 added.