What is on the printable ring size chart
- Calibration bar · exactly 100 mm, with 10 mm ticks
- Actual-size ring size chart · 21 circles for US sizes 3 to 13 in half sizes, each labelled with its inside diameter in mm
- Strip sizer · cut out, wrap your finger, read the size at the slit
- Bank card outline · 85.60 × 53.98 mm, a second check if you have no ruler
Do printable ring sizers work?
Yes, if the sheet prints at the right size. The file itself is not the weak point: the printer is. We checked our own PDFs on 16 November 2026 by rendering both sheets at 600 dots per inch and measuring them:
| What we measured | A4 PDF | US Letter PDF |
|---|---|---|
| Calibration bar | 100 mm (100.16 mm including the end tick lines) | 100 mm (100.16 mm including the end tick lines) |
| 21 sizing circles, US 3 to 13 | Every circle within 0.07 mm of its stated diameter | Every circle within 0.08 mm of its stated diameter |
A quarter US size is about 0.2 mm in diameter, so the files are accurate to well under a quarter size. What can go wrong is the print: a printer or print dialog that shrinks the page shrinks every circle and every mark on the strip with it.
What a shrunken print does to your size
If the sheet prints smaller than 100%, each circle is smaller than its label, so a ring will match a circle that is labelled too large. The same happens with the strip. This is the effect on the circle labelled US 7, which should be 17.32 mm across:
| Print scale | Circle labelled US 7 measures | That is really | Your result |
|---|---|---|---|
| 100% | 17.32 mm | US 7 | Correct |
| 99% (bar reads 99 mm) | 17.15 mm | About US 6¾ | About a quarter size too large |
| 97% (bar reads 97 mm) | 16.80 mm | About US 6⅓ | More than half a size too large |
| 95% (bar reads 95 mm) | 16.46 mm | About US 6 | About a full size too large |
Figures use the US scale formula in how we calculate. If your bar reads less than 99 mm, reprint before you measure.
Three checks for an accurate print
- Print at Actual size. In the print dialog choose Actual size or 100%. Turn off Fit to page and Shrink to fit.
- Measure the 100 mm bar. Lay a ruler along it. If it is off by more than 1 mm, change the print setting and print again.
- Check with a bank card. No ruler? Any standard bank card should fit the printed outline exactly.
How to print at 100%
| Printing from | Setting to choose |
|---|---|
| Adobe Acrobat or Reader | Page Sizing: Actual size |
| Chrome or Edge | More settings › Scale: Default or Custom 100; untick Fit to page if shown |
| Mac Preview | Scale: 100%; untick Scale to fit |
| Phone or tablet | Many mobile print dialogs scale without asking. Print from a computer if you can, and always check the bar. |
Use the PDF that matches the paper in your printer. Printing the A4 file on US Letter paper, or the other way round, can make the print dialog scale the page.
Circles or strip: which to use
| Circles (ring that fits) | Strip sizer (your finger) | |
|---|---|---|
| Measures | The inside diameter of a ring | The circumference of your finger |
| Best when | You have a ring that fits the same finger | You have no ring, or the ring is for a new finger |
| Watch out for | Thick bands hiding the line; match the inside edge | Pulling too tight; check it passes the knuckle |
How to use the circles
- Place a ring that fits the same finger flat on the circles.
- Find the circle whose line sits just inside the ring’s inner edge.
- If the ring falls between two circles, it is between those sizes: the circles go up in half sizes.
- Check the size in the ring size chart in mm using the diameter printed under the circle.
How to use the ring sizer strip
- Cut along the outline and cut the slit at the marked end.
- Wrap the strip around the base of your finger, numbers facing out, and feed the pointed end through the slit.
- Pull until it is snug but not tight, and check it still passes over your knuckle.
- Read the size at the slit. If you sit between two marks, choose the larger for a wide band.
If the print looks wrong
| Problem | Fix |
|---|---|
| Bar is shorter than 100 mm | The page was scaled down. Choose Actual size or 100% and turn off Fit to page. |
| Edges are cut off | You may have the wrong paper size. Download the PDF that matches your paper. |
| Printing from a phone | Phone print dialogs often scale silently. Check the bar every time. |
| No printer | Use a strip of paper and a ruler instead: see the paper strip method, or measure a ring on your screen with the online ring sizer. |
Once you have a measurement, look it up in the mm and cm chart or enter it in the calculator. Prefer another method? See all six ways to measure ring size at home.